Automatic Glass Cutting Machine
The Automatic Glass Cutting Machine combines automatic vacuum loading with CNC precision scoring in a single, high-speed platform. Driven by an advanced OMRON CK3M multi-axis controller and linear-motor bridge, it executes complex cut patterns at up to 15m/min with ±0.15mm accuracy. The integrated Eos-Nc optimization software plans every layout for maximum yield, while 4-point scanning and electromagnetic proportional valve control deliver clean, easy-to-break score lines on glass from 2–19mm.
How It Works
Five stages from raw sheet to separated pieces — the complete automatic cutting workflow.
Why This Cutting Machine
Six features engineered for precision, speed, and effortless operation.
Linear-Motor Bridge Drive
Both X and Y axes use a direct linear motor drive with no transmission wear. Minimal wear, low noise, and easy maintenance keep the bridge at peak precision and speed over the machine's lifetime.
4-Point Scanning Alignment
Ensures superior precision through 4-point scanning. Combined with proximity positioning and bidirectional cutting, the machine optimizes every path for maximum efficiency and accuracy.
Proportional Valve Tool Control
An electromagnetic proportional valve precisely controls the cutting head, ensuring clean, easy-to-break scores with no water-wave patterns or bevels — even on thick plates.
Eos-Nc Smart Optimization
The self-developed Eos-Nc software handles nesting, path planning, and machine control in one unified interface. One-touch workflow from file import to machine startup lowers the operator skill requirement.
Reinforced Full-Load Structure
The frame and drive system are structurally engineered to remain stable under full load. Continuous multi-shift production with consistent quality panel after panel.
24/7 Support & Lifetime Service
Every cutting machine ships with lifetime technical support, remote diagnostics capability, and a dedicated service hotline — for the life of the machine.
Up to 15m/min Cutting Speed
Linear-motor bridge with a 50µs control cycle executes complex shapes at speed without losing accuracy — keeping your line at maximum throughput.
Technical Specs
Every parameter engineered for precise, repeatable cutting.
How It Compares
Automatic CNC cutting vs. manual and standard CNC alternatives.
Hanwin Automatic Cutting leads in Precision (95), Yield (90), and Automation (95) — combining ±0.15mm accuracy with one-touch automated workflow for maximum output.
Where It Excels
From architectural panels to thin solar glass — one cutting machine, every application.
Architectural Curtain Wall
High-Volume Production
Large-format curtain wall panels demand consistent accuracy across thousands of pieces. The automatic cutting machine handles glass up to 6100×3300mm with ±0.15mm repeatability, making it the standard for curtain wall fabrication facilities worldwide.
Choose Your Configuration
Three tiers from essential cutting to fully automated smart-factory integration.
Standard
Essential CuttingProfessional
Full AutomationEnterprise
Smart Factory ReadyKeep It Running
Five essential maintenance practices to protect your glass and maximize uptime.
Clean the cutting table surface, scoring wheel, and conveyor rollers at the end of each shift. Remove glass dust and debris from the linear-motor guide rails. Inspect the scoring wheel for chips or wear — replace when score quality degrades.
Run a test cut on a scrap piece and measure diagonals with a precision ruler. If accuracy drifts beyond ±0.20mm, recalibrate the CNC axes following the service manual procedure. Log all calibration results.
Check compressed air supply pressure (0.5–0.7 MPa), drain the air filter separator, and inspect pneumatic cylinders for leaks. Lubricate the scoring head piston with approved pneumatic oil.
Inspect all electrical connections, terminal blocks, and cable carriers for looseness or wear. Check servo and linear-motor encoder connections. Update the Eos-Nc software if a new version is available.
Perform a full machine calibration using laser alignment tools. Replace conveyor belt tensioners, scoring wheel bearings, and guide rail bushings as needed. Conduct a full safety system test including light curtains and emergency stops.
Common Questions
Everything you need to know about the Automatic Glass Cutting Machine.
The standard configuration handles glass up to 6100×3300mm (approximately 20×10 feet). Smaller formats are also supported, with a minimum glass size of 300×300mm. Custom table sizes are available on request.
The machine delivers ±0.15mm accuracy on straight cuts and ±0.20mm on diagonals, maintained through closed-loop feedback and regular calibration. This meets the requirements of architectural, automotive, and solar glass production.
Yes. The Eos-Nc software natively supports DXF and DWG file import from AutoCAD, SolidWorks, and other CAD platforms. You can also create programs directly on the touchscreen HMI or scan physical templates with the optional CCD camera system.
The machine handles float glass, tempered glass (before tempering), laminated glass, coated glass (including Low-E), ultra-clear glass, and patterned glass. Electromagnetic proportional valve control adjusts scoring pressure across the 2–19mm thickness range to suit different glass hardness levels.
The linear-motor bridge cuts at up to 15m/min with a 50µs control cycle, executing complex shapes without losing accuracy. Combined with a 20–50 second automatic loading cycle, 8-hour output reaches high-volume production targets.
Every machine ships with a 1-year warranty, lifetime technical support, remote diagnostics capability (on Professional and Enterprise configurations), and access to our global spare parts network. Our service team responds within 24 hours for all technical enquiries.
Get a Quote
Tell us about your production needs and we'll recommend the right cutting machine configuration.
Contact Information
Pre-configured for Automatic Cutting
Your enquiry is pre-tagged for our Automatic Glass Cutting Machine. Include your glass sizes, thickness range, and daily volume for a faster response.
Cut Faster with Zero Compromise
Automatic vacuum loading, linear-motor precision, and Eos-Nc optimization — clean, accurate scores on every sheet, 2–19mm.